Extreme Networks Summit WMScanner Скачать руководство пользователя страница 158 | Manualshive

Страница: 158 / 217

Extreme Networks Summit WMScanner Скачать руководство пользователя страница 158

Measurement Surveys

Summit WMScanner Users Guide

156

●

The Name field:

Within a drawing file, all RFID readers must have a unique name. That is, the name

entered in the

Name Edit

Dialog Box cannot be used for any other RFID reader within the drawing. If

you accidentally enter a duplicate name in the box, Summit WMScanner displays a warning
message.

●

The Antenna Button:

This option allows you to edit and configure the antenna associated with the

RFID reader. See

“Adding/Editing the Antenna” on page 157

●

Hardware Configuration: Using the hardware configuration you can edit the description field, the IP
address field, and the MAC address field. The description field can be used to give additional
information about the RFID reader. By default the description field displays the RFID model name.

●

Hardware Position:

The hardware position field defines the location of the RFID reader. This enables

you to enter the absolute position of the RFID reader on the floor within the building. All
coordinates are given relative to the origin (also called the Floor Alignment Point) of the building
coordinate system. You can also change the floor on which a RFID reader is deployed using the
drop-down menu of the Located on Floors option. When a RFID reader is moved to some other
floor, the antennas associated with it are also moved to that floor.

Click

OK

or

Cancel

to go back to the

Edit/Remove

RFID dialog box.

«
...
156
157
158
159
160
...
»

Содержание Summit WMScanner


























































































































































































































Отзывы:

Нет отзывов