manualshive.com logo in svg

Extreme Networks Summit WMScanner, Руководство пользователя, Страница: 153 / 217

Поделиться
Скачать
Extreme Networks Summit WMScanner Скачать руководство пользователя страница 153

Summit WMScanner Users Guide

151

Moving Sensors

The Move Sensor command is a quick way to change the location of a sensor which has already been 
placed. To do this, select 

Equipment > Sensor > Move Sensor

. The 

Move Sensor

 dialog box displays.

 

From the Move Sensor dialog box, select the sensor that you wish to move and click Move. Your pointer
will take on the appearance of the sensor that you selected from the list. Move the sensor to the desired
location and left-click to place it. You may also move multiple sensors simultaneously by selecting more
than one sensor before clicking Move. Click Finished after you are done moving sensors. 

Copying Sensors

The Copy Sensors menu command works very similar to the Move Sensor command. To copy one or
more sensors on a floor, select Equipment > Sensor > Copy Sensor. The Copy Sensor dialog box appears

Содержание Summit WMScanner


























































































































































































































Отзывы:

Нет отзывов