Extreme Networks Summit WMScanner Скачать руководство пользователя страница 132 | Manualshive

Страница: 132 / 217

Extreme Networks Summit WMScanner Скачать руководство пользователя страница 132

Measurement Surveys

Summit WMScanner Users Guide

130

Show All Markers

To show the display of all measurement text in the drawing, click

Measurement Survey > Display

Measurement Data > Show All Markers

.

Reposition and Scale

Selecting the

Measurement Survey > Display Measurement Data > Reposition and Scale

command allows

you to move existing measurement points in the drawing. You have the option of relocating individual
measurement points or adjusting the scale of an entire measurement run. When adjusting the scale of a
run, the marker’s position relative to each other remains the same but the distance between them
increases or decreases depending on your scaling.

Hide All Markers

To hide the display of all measurement text in the drawing, click

Measurement Survey > Display

Measurement Data > Hide All Markers

.

Configure Markers/Tracklines

To configure Markers/Tracklines, select

Measurement Survey > Display Measurement Data > Configure

Markers/Tracklines.

Type or select Measurement Marker Size and Trackline Arrowhead Size.

Managing Access Points

The following workflow example provides an overview of the primary steps for selecting, placing, and
configuring access points.

«
...
130
131
132
133
134
...
»

Содержание Summit WMScanner


























































































































































































































Отзывы:

Нет отзывов