Extreme Networks Summit WMScanner Скачать руководство пользователя страница 120 | Manualshive

Страница: 120 / 217

Extreme Networks Summit WMScanner Скачать руководство пользователя страница 120

Measurement Surveys

Summit WMScanner Users Guide

118

Following the above steps will result in a grid coverage being displayed that will pin-point the location
of the AP with the MAC you selected. If this MAC is not in your infrastructure, then this process will
help you locate unauthorized or rogue APs. Otherwise, it will help you verify the location of an AP that
is part of your infrastructure.

Verifying the Channel and SSID Settings of Access Points

You can quickly verify the channel settings of all APs that were visible during the measurement runs
present in or imported into the drawing. Just select the

Filter By:

drop-down box and choose

Channel.

Then you can look at the resulting list and all the MACs will be grouped according to their channel.
Filtering by SSID allows you to do the same thing with respect to the SSID.

«
...
118
119
120
121
122
...
»

Содержание Summit WMScanner


























































































































































































































Отзывы:

Нет отзывов