Extreme Networks Summit WMScanner Скачать руководство пользователя страница 112 | Manualshive

Страница: 112 / 217

Extreme Networks Summit WMScanner Скачать руководство пользователя страница 112

Measurement Surveys

Summit WMScanner Users Guide

110

The following is an example of Expected Legacy Data Rate visualization. Hovering the mouse over the
grid vertices displays the data at particular points in the visualization:

NOTE

Data Rate grids are displayed as shaded if visualized in the Flat Shaded, Edges On mode (View > Shade > Flat
Shaded, Edges On).

Noise Visualization

The Noise visualization mode allows you to view regions where a certain level of noise occurs. The
regions are displayed as color coded grids on the drawing. This view shows the worst noise at each
point, which makes the visualization ideal for identifying noise problems within your facility. To
visualize noise, choose the

Noise

option:

«
...
110
111
112
113
114
...
»

Содержание Summit WMScanner


























































































































































































































Отзывы:

Нет отзывов