Extreme Networks Summit WMScanner Скачать руководство пользователя страница 108 | Manualshive

Страница: 108 / 217

Extreme Networks Summit WMScanner Скачать руководство пользователя страница 108

Measurement Surveys

Summit WMScanner Users Guide

106

An example of channel visualization is shown on the next page. Hovering the mouse over the grid
vertices displays more information about the data at particular points in the visualization:

This visualization, by default, colors the 20 MHz 802.11 channels and all combinations of their 40 MHz
802.11 channels in the same color. For example, all grid vertices serving the channels 5(-1), 5 and 5(+1)
are shown in the same color. You can select new colors for these channels depending upon your
requirements.

NOTE

Channel grids are only displayed as shaded when in the Flat Shaded, Edges On mode (View > Shade > Flat Shaded,
Edges On).

Coverage Visualization

The Coverage visualization mode allows you to view regions where a certain level of RSSI (

Received

Signal Strength Intensity

) occurs. The regions are displayed as color-coded grids directly on the drawing.

You can use this view to verify network coverage, identify and locate rogue access points (APs), and

«
...
106
107
108
109
110
...
»

Содержание Summit WMScanner


























































































































































































































Отзывы:

Нет отзывов