manualshive.com logo in svg

Extreme Networks ExtremeWireless AP560h, Руководство по установке, Страница: 38 / 40

Поделиться
Скачать
Extreme Networks ExtremeWireless AP560h Скачать руководство пользователя страница 38

This device is restricted to indoor usage only.

Warning
FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment. This equipment should be installed and
operated with a minimum distance of 26 cm between the radiator and your body.

Note
For products available in the USA and Canada markets, only channel 1~11 can be operated.
Other channels cannot be selected.

Industry Canada (IC) Notice

Industry Canada (IC) Notice

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and
Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two
conditions: (1) This device may not cause interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation of the device.

Cet appareil contient des émetteurs / récepteurs exempts de licence qui sont conformes au (x) RSS (s)
exemptés de licence d'Innovation, Sciences et Développement économique Canada. L'opération est
soumise aux deux conditions suivantes: (1) Cet appareil ne doit pas provoquer d'interférences. (2) Cet
appareil doit accepter toute interférence, y compris les interférences susceptibles de provoquer un
fonctionnement indésirable de l'appareil.

Warning
IC Radiation Exposure Statement:
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20 cm
between the radiator & your body.

Warning
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux rayonnements ISED établies pour
un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum
de 20 cm de distance entre la source de rayonnement et votre corps.

European Waste Electrical and Electronic Equipment (WEEE) Notice

Industry Canada (IC) Notice

Regulatory and Compliance Information

38

ExtremeWireless™ AP560h Access Point

Содержание ExtremeWireless AP560h









































Отзывы:

Нет отзывов