Extreme Networks ExtremeSwitching X440-G2 Series Скачать руководство пользователя страница 54

Страница: 54 / 413

Figure 63: X460-G2-24p-24hp-10GE4 Front Panel

1 = Stack number indicator

4 = PoE+ 10/100/1000BASE-T ports

2 = Console port/Ethernet management port

5 = PoE+ 10/100/1000BASE-T ports with half-duplex

3 = USB port

6 = SFP+ 10GBASE-X ports

Figure 64: X460-G2-24p-24hp-10GE4 Rear Panel

1 = TM-CLK (clock) slot cover

4 = Blank power supply cover

2 = VIM slot cover

5 = Power supply slot

3 = Fan module slot

Note
It is not possible to collect statistics on packet collisions for the X460-G2-24p-24hp-10GE4
switch.

ExtremeSwitching X460-G2-16mp-32p-10GE4 Switch Ports and Slots

X460-G2-16mp-32p-10GE4 switch ports and slots include:

•

16 front panel PoE+ ports of 100/1000/2.5G BASE-T (ports 1-16).

•

32 front panel PoE+ ports of 10/100/1000BASE-T (ports 17-48).

•

Four ports of 10G SFP+ (ports 49-52, with two of these ports configurable to be stacking ports)

•

One front panel USB port

•

Ethernet management port 1 x 10/100/1000BASE-T

•

Serial console port implemented as an RJ45 connector used to connect a terminal and perform local
management.

•

One rear panel VIM slot

•

One rear panel TM-CLK (clock) slot

ExtremeSwitching Switches

ExtremeSwitching and Summit Switches: Hardware Installation Guide

Содержание ExtremeSwitching X440-G2 Series






























































































































































































































































































































































































































Результаты поиска

Содержание ExtremeSwitching X440-G2 Series

Отзывы:

Похожие инструкции для ExtremeSwitching X440-G2 Series

Бренды по названию

Популярные бренды

Extreme Networks ExtremeSwitching X440-G2 Series, Руководство по установке оборудования

Результаты поиска

Содержание ExtremeSwitching X440-G2 Series

Отзывы:

Похожие инструкции для ExtremeSwitching X440-G2 Series

Бренды по названию

Популярные бренды