Extreme Networks ExtremeSwitching X440-G2 Series Скачать руководство пользователя страница 274 | Manualshive

Страница: 274 / 413

background image

8 Connect the power cord to the power supply and to a grounded AC power outlet.

Warning
Always be sure that the source outlet is properly grounded before plugging the AC power
cord into the AC power supply.

9 If the power supply is equipped with a power cord retainer, use the retainer to secure the power cord

to the power supply.

Replacing a Summit 1100 W AC Power Supply

The Summit 1100 W AC power supplies are compatible with the X450-G2 and X460-G2 PoE switches.
Part number 10941 is compatible with ExtremeSwitching X465 PoE switch models.

These switches have two bays for hot-swappable power supplies. In a switch with a redundant power
configuration, you can replace one Summit AC power supply without powering down the switch.

You need the following tools and materials to replace a Summit 1100 W AC power supply:

•

Thermal protective gloves

•

AC power cord, if you will not be re-using the cord from the removed power supply

To replace a Summit 1100 W AC power supply, follow these steps:

1 Disconnect the AC power cord from the wall outlet and from the power supply.
2 Note the orientation of the installed power supply, and the location of the latching tab at the right of

the unit.

Replacing AC Power Supplies

ExtremeSwitching and Summit Switches: Hardware Installation Guide

274

«
...
272
273
274
275
276
...
»

Содержание ExtremeSwitching X440-G2 Series






























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ExtremeSwitching X440-G2 Series

Бренд: ABB Страницы: 32

Бренд: ABB Страницы: 44

Бренд: ABB Страницы: 15

Бренд: IBM Страницы: 88

Бренд: DANLERS Страницы: 2

Бренд: Eaton Страницы: 8

Бренд: NETGEAR Страницы: 8

Бренд: KCC Страницы: 6

Бренд: Icy Box Страницы: 6

Бренд: 3Com Страницы: 62

Elinx EIR510-2MC-T

Бренд: B&B Electronics Страницы: 107

SIL IntelliPoint RF S*R*L Series

Бренд: Ametek Страницы: 93

Бренд: Topex Страницы: 170

Бренд: ADC Страницы: 75

Бренд: Moxa Technologies Страницы: 7

Бренд: TRENDnet Страницы: 2

3CB9E7 - CoreBuilder 9000 Chassis Switch

Бренд: 3Com Страницы: 132

Бренд: C4i Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды