Extreme Networks ExtremeSwitching X440-G2 Series Скачать руководство пользователя страница 102 | Manualshive

Страница: 102 / 413

background image

Table 36: STK-RPS-150PS LED Status Definitions

Power LED

Meaning

Recommended Action

Green, solid

AC input to power supply is within
specifications

None

Off

AC input power to power supply is out
of specification.

1

Check AC power cord connection to the
power supply.

2 Check AC power at the power outlet.
3 Swap power cord for a known good one.
4 If the problem persists, contact Extreme

Networks for support.

For technical specifications, see

STK-RPS-150PS and RPS Shelves Technical Specifications

STK-RPS-1005PS Redundant Power Supply

Notice
Extreme Redundant Power Supplies (RPS) do not support the ability for the RPS to be
connected to an operational switch. Connecting an RPS to an operational switch can have an
adverse effect on the switch. It is best practice that both the switch and the RPS be powered
down prior to cabling them together. Once the cabling is completed, turn on the RPS, then
turn on the switch.

The STK-RPS-1005PS provides load sharing, backup, or additive PoE power to some Extreme Networks
802.3at PoE-compliant stackable switch models. If the switch loses power from its internal power
supply, the STK-RPS-1005PS can provide up to 1005 W maximum operating power (180 W system
power and 740 W PoE power) to support switch operation and the 55 VDC necessary to support 55
VDC/data connections to powered devices.

The power supply ships with the following:

•

AC power cable

•

RPS cable

•

Four rubber feet (for flat surface installation)

The STK-RPS-1005PS is compatible with the ExtremeSwitching X440-G2-48p-10GE4 switch.

Figure 100: STK-RPS-1005PS Front Panel

Power Supplies for Use with Your Switch

ExtremeSwitching and Summit Switches: Hardware Installation Guide

102

«
...
100
101
102
103
104
...
»

Содержание ExtremeSwitching X440-G2 Series






























































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ExtremeSwitching X440-G2 Series

Бренд: H3C Страницы: 32

Бренд: H3C Страницы: 22

Бренд: H3C Страницы: 488

Бренд: H3C Страницы: 3

Бренд: H3C Страницы: 8

Бренд: H3C Страницы: 25

Бренд: H3C Страницы: 31

Бренд: H3C Страницы: 23

Бренд: H3C Страницы: 24

Бренд: H3C Страницы: 126

Бренд: H3C Страницы: 42

Бренд: H3C Страницы: 32

Бренд: H3C Страницы: 13

Бренд: H3C Страницы: 16

Бренд: H3C Страницы: 39

SANbox 5000 Series

Бренд: Qlogic Страницы: 8

SilverStorm 9000

Бренд: Qlogic Страницы: 50

Бренд: FS Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды