Extreme Networks ExtremeSwitching VDX 6740 Скачать руководство пользователя страница 105 | Manualshive

Страница: 105 / 135

background image

3. Review the device system log for errors. Any errors detected during POST are written to the system log, accessible through the

show logging raslog

command.

For information about all referenced commands, and on accessing the error log, refer to the

Extreme Network OS Command

Reference

. For information about error messages, refer to the

Extreme Network OS Message Reference

.

Powering off the device

To power off the VDX 6740, set the on/off switch to the "off" position on both power supplies.

To power off the per power supply VDX 6740T, you must unplug both power supplies.

Thermal operations

Thermal sensors located in the device sense temperature levels during operation to drive fan speed. In cases of extreme temperature, a
RASlog message is generated warning of automatic system shutdown in two minutes, at which time the system shuts down. When the
system shuts down, fans continue to run at high speed.

Device maintenance

These devices are designed for high availability and low failure; not require any regular physical maintenance. The SFP+ optical
transceivers and diagnostic tests are described in the following sections.

Installing an Ethernet SFP+ transceiver

Only the VDX 6740 supports 10 GbE SFP+ transceivers. Complete the following steps to install an SFP+ transceiver.

1. Remove any protector plugs from the transceivers and the ports.
2. Making sure that the bail (wire handle) is in the unlocked position, place the SFP+ transceiver in the correctly oriented position on

the port, as shown in the following figure.

3. Slide the SFP+ transceiver into the port until you feel it click into place; then close the bail.

Device maintenance

ExtremeSwitching VDX 6740 Hardware Installation Guide

9036108-00

105

«
...
103
104
105
106
107
...
»

Содержание ExtremeSwitching VDX 6740








































































































































Отзывы:

Нет отзывов

Похожие инструкции для ExtremeSwitching VDX 6740

D DGS-3048 DGS-3048

Бренд: D-Link Страницы: 3

Бренд: D-Box Страницы: 27

LINK 14201-20 - DATASHEET FOR TOSHIBA PHONES

Бренд: Jabra Страницы: 4

SMALL OFFICE CyberSwitch 150

Бренд: Cabletron Systems Страницы: 106

Бренд: LONG-JOIN Страницы: 2

24-Port Gigabit Switch

Бренд: Belkin Страницы: 2

FL SWITCH SFN 16TX

Бренд: Phoenix Contact Страницы: 6

Бренд: LevelOne Страницы: 35

Бренд: EtherWAN Страницы: 239

OmniAccess 6000

Бренд: Alcatel-Lucent Страницы: 76

Бренд: UniFi Страницы: 13

Бренд: Shenzhen Kinan Technology Страницы: 27

Бренд: Manhattan Страницы: 2

Бренд: KanexPro Страницы: 49

Бренд: Honeywell Страницы: 180

Бренд: Honeywell Страницы: 116

Бренд: Honeywell Страницы: 204

Бренд: Kenwood Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды