Extreme Networks ExtremeSwitching SLX 9250 Скачать руководство пользователя страница 74

Страница: 74 / 97

Power Options

Table 28: SLX 9250 Switch Power Options

SLX 9250 Switch

750 W AC power supply:

Part # XN-ACPWR-750W-F (front-to-back)

Part # XN-ACPWR-750W-R (back-to-front)

AC Input: 100-120/200-240 VAC, 50/60 Hz

3.5/1.8 A max. for each PSU

PSU Input Socket: IEC 320 C14

Power cord input plug: IEC 320 C13
750 W DC power supply:

Part # XN-DCPWR-750W-F (front-to-back)

Part # XN-DCPWR-750W-R (back-to-front)

DC Input: -54 VDC, 7.0 A max. for each PSU

Power Consumption

Table 29: SLX 9250 Switch Power Consumption

Operating Mode

Test Conditions

Power Consumption

Fan Duty Traffic

Load

Port

Status

Packet

Length

(Bytes)

Dual Power:

PSU1

Dual Power:

PSU2

Single

Power:

PSU1

Empty mode

85%

Down

152.6 W

145.5 W

285.9 W

Standby mode

85%

157.6 W

151.5 W

297.2 W

Typical mode

85%

70%

1,518

165 W

159.8 W

313.6 W

Stress mode

100%

256

207.8 W

204.5 W

406.o W

Power and Heat Dissipation

Table 30: SLX 9150 Power and Heat Dissipation

Switch Model

Minimum Heat

Dissipation

(BTU/hr) (Idle, no

ports linked)

Minimum Power

Consumption (Watts)

(Idle, no ports linked)

Maximum Heat

Dissipation

(BTU/hr) (Fans

high, all ports

100% traffic)

Maximum Power

Consumption

(Watts) (Fans

high, all ports

100% traffic)

SLX9250-32C-AC-F 734 BTU/ hr

215W

1573 BTU/ hr

461W

SLX9250-32C-AC-R 734 BTU/ hr

215W

1573 BTU/ hr

461W

Power Options

ExtremeSwitching SLX 9250 Technical Specifications

ExtremeSwitching SLX 9250 Hardware Installation Guide

Содержание ExtremeSwitching SLX 9250


































































































Результаты поиска

Содержание ExtremeSwitching SLX 9250

Отзывы:

Похожие инструкции для ExtremeSwitching SLX 9250

Бренды по названию

Популярные бренды

Extreme Networks ExtremeSwitching SLX 9250, Руководство по установке оборудования

Результаты поиска

Содержание ExtremeSwitching SLX 9250

Отзывы:

Похожие инструкции для ExtremeSwitching SLX 9250

Бренды по названию

Популярные бренды