background image

Table 21: SLX 9250 Software Specifications (continued)

Software Specifications

Description

Maximum number of MCT switches

2

Maximum number of Bridge Domains

4096

Maximum IPv4 unicast routes

128,000

Maximum IPv6 unicast routes

10,000

Maximum IPv4 host routes

47,000

Maximum IPv6 host routes

33,000

Maximum jumbo frame size

9,126 bytes

QoS priority queues (per port)

8

IEEE Compliance

• IEEE 802.1D Spanning Tree Protocol
• IEEE 802.1s Multiple Spanning Tree
• IEEE 802.1w Rapid Reconfiguration of Spanning

Tree Protocol

• IEEE 802.3 Ethernet
• IEEE 802.3ad Link Aggregation with LACP
• IEEE 802.3ab 1000BASE-T
• IEEE 802.3z 1000BASE-X
• IEEE 802.3ba / 80 2.3bm 40 GBASE-X and 100

GBASE-X

• IEEE 802.1Q VLAN Tagging
• IEEE 802.1p Class of Service Prioritization and

Tagging

• IEEE 802.1v VLAN Classification by Protocol and

Port

• IEEE 802.1AB Link Layer Discovery Protocol

(LLDP)

• IEEE 802.3x Flow Control (Pause Frames)
• IEEE 802.3ae 10 GBASE-X
• IEEE 802.3 10 GBASE-T (up to 100 m using

Cat6a cabling or better)

Weights and Physical Dimensions

Table 22: SLX 9250 Switch Unpackaged Dimensions

SLX9250-32C (SLX 9250-32C base)

Height: 4.34 cm (1.71 in)

Width: 43.96 cm (17.31 in)

Length: 53.95 cm (21.24 in)

XN-FAN-001-F: Fan unit, front-to-back or XN-FAN-001-R:

Fan Unit back-to-front

Height: 4.0 cm (1.57 in)

Width: 4.0 cm (1.57 in)

Length: 13.4 cm (5.28 in)

ExtremeSwitching SLX 9250 Technical Specifications

Weights and Physical Dimensions

ExtremeSwitching SLX 9250 Hardware Installation Guide

71

Содержание ExtremeSwitching SLX 9250


































































































Отзывы: