Extreme Networks ExtremeSwitching 5520 Series Скачать руководство пользователя страница 84 | Manualshive

Страница: 84 / 162

background image

Configuring the Switch's IP Address for the Management VLAN

You can configure the switch's IP address for the management virtual LAN (VLAN).

Note
The management port is part of the

mgmt

VLAN. This VLAN membership cannot be changed.

Log in to the management console, connect to the switch, and follow these steps.

1. Assign a name, IP address, and default subnetwork mask for the VLAN as shown in the following

example.

configure vlan

vlan_name

ipaddress

nn.nn.nn.nn

255.255.255.0

Your changes take effect immediately.

2. Enter

save

to save your configuration changes so that they will be in effect after the next system

reboot.

Note
For more information about saving configuration changes, see the

ExtremeXOS 31.1 User

.

The configuration is saved to the configuration database of the switch.

Changing the Switch OS via the Bootloader Menu

Extreme recommends onboarding your switch with ExtremeCloud™. Log in or create your XIQ
administrator account in order to select your switch operating system with XIQ at

extremecloudiq.com

ExtremeXOS is the default operating system for the 5520 Series. You can change the switch OS from
the Bootloader menu on initial activation only by completing the following steps:

1. Using a terminal emulator such as PuTTY or TeraTerm, connect to the switch using the serial port

connection.
Be sure that your serial connection is set properly:

•

Baud rate: Baud rate: 115200

•

Data bits: 8

•

Stop bit: 1

2. Once the switch is powered on, after seeing the "5520 Boot Menu" screen, press the

[spacebar]

key

within 30 seconds.

3. Use the

down-arrow

key to select

Change the switch OS to VOSS

, then select

Enter

.

The switch will install VOSS, then reset. Once the NOS is selected, the "5520 Boot Menu" will only wait
for 3 seconds before continuing.

To change the switch OS if you take no action during the initial boot, see

Changing the Switch OS via

the Startup Menu

on page 85

Configuring the Switch's IP Address for the
Management VLAN

Activating and Verifying the Switch

84

ExtremeSwitching 5520 Series Hardware Installation Guide

«
...
82
83
84
85
86
...
»

Содержание ExtremeSwitching 5520 Series



































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ExtremeSwitching 5520 Series

Бренд: Panasonic Страницы: 20

Бренд: Panasonic Страницы: 281

Бренд: KanexPro Страницы: 16

Бренд: H3C Страницы: 90

DES-3224 - Switch

Бренд: D-Link Страницы: 75

3C16710 - OfficeConnect 8/TPM Hub

Бренд: 3Com Страницы: 130

Бренд: E&C Страницы: 10

Бренд: Quintech Страницы: 2

Бренд: N-Tron Страницы: 16

Master View CS-74A

Бренд: ATEN Страницы: 16

Бренд: DX Engineering Страницы: 4

Бренд: National Instruments Страницы: 12

Бренд: Comm-Tec Страницы: 10

kontron KSwitch D1 UGPD

Бренд: S&T Страницы: 40

NSwitch Outdoors

Бренд: Moxa Technologies Страницы: 30

QSW-M2108 Series

Бренд: QNAP Страницы: 28

CrossPoint 42 HVA

Бренд: Extron electronics Страницы: 46

Бренд: Kramer Страницы: 85

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды