Extreme Networks ExtremeSwitching 210-12p-GE2 Скачать руководство пользователя страница 36

Страница: 36 / 81

Installing Your 210 or 220 Switch

Safety Considerations for Installing Switches
Pre-installation Requirements
Attaching a 24- or 48-Port Switch to a Rack
Mounting 12-Port Switches
Installing a Switch on a Desktop or Other Flat Surface
Installing Optional Components
Connecting Power to the Switch
Connecting Network Interface Cables

Before you attempt to install or remove an Extreme Networks switch, read the precautions in

Safety

Considerations for Installing Switches

on page 37.

ExtremeSwitching switches fit into standard 19-inch equipment racks.

There are additional mounting options for 12-port switch models. They can be mounted on a wall,
individually in a rack, or side by side in a rack.

The provided rack-mounting brackets attach to the front of the switch and are adaptable to either a
front-mount or mid-mount installation. Optional rear-mounting brackets are also included for four-post
racks or cabinets.

The installation process includes the following tasks:

1 Prepare the site for installing the switch.

See

Pre-installation Requirements

on page 37.

2 Install the switch in a rack or on a desktop.

See

Attaching a 24- or 48-Port Switch to a Rack

on page 38 or

Installing a Switch on a Desktop or

Other Flat Surface

on page 48.

For 12-port switch models, see

Mounting 12-Port Switches

on page 39.

3 Install optional optical transceivers.

See the instructions in

Installing Optional Components

on page 49.

4 Connect power to the switch.

See

Connecting Power to the Switch

on page 50.

5 Connect network interface cables.

See

Connecting Network Interface Cables

on page 50.

6 Perform initial network connection and configuration.

See

Basic Configuration for Your Switch

on page 60.

ExtremeSwitching 210 and 220 Series Switches: Hardware Installation Guide

Содержание ExtremeSwitching 210-12p-GE2


















































































Результаты поиска

Содержание ExtremeSwitching 210-12p-GE2

Отзывы:

Похожие инструкции для ExtremeSwitching 210-12p-GE2

Бренды по названию

Популярные бренды

Extreme Networks ExtremeSwitching 210-12p-GE2, Руководство по установке оборудования

Результаты поиска

Содержание ExtremeSwitching 210-12p-GE2

Отзывы:

Похожие инструкции для ExtremeSwitching 210-12p-GE2

Бренды по названию

Популярные бренды