background image

Note:

When you remove an optic or a copper or fiber cable from Combo ports (47 and 48) in VSP
4850GTS or VSP 4850GTS-PWR, the port Link/Activity LEDs graphically represented in EDM
do not reflect the correct LED status on the switch. The port Link/Activity LEDs in EDM remain
solid green even after an automatic refresh of EDM. You must logout and login to EDM to see
the correct LED status.

Viewing hardware information

About this task

Perform the following procedure to view system status and technical information about the VSP

4450GSX-PWR+ hardware components. You can view information about the switch (such as

location), chassis (type, serial number, and base MAC address), temperature, power supplies, fans,

cards, system errors, port locks, topology status, and message control information.

Procedure

1. Log on to the switch to enter User EXEC mode.

2. View hardware information:

show sys-info [card | fan | led | power | temperature | uboot]

Example

Viewing hardware information on VSP 4450GSX-PWR+ switch:

VSP-4450GSX-PWR+:1>show sys-info

General Info :

        SysDescr     : VSP-4450GSX-PWR+ (w.x.y.z)

        SysName      : VSP-4450GSX-PWR+

        SysUpTime    : 0 day(s), 00:06:12

        SysContact   : http://www.extremenetworks.com/contact/

        SysLocation  : 9 Northeastern Blvd,Salem,NH. 03079

Chassis Info:

        Chassis            : 4450GSX-PWR+

        ModelName          : 4450GSX-PWR+

        BrandName          : Extreme Networks.

        Serial#            : SDNIV50S1016

        H/W Revision       : R0B

        H/W Config         :  R0B

        Part Number        :

        NumSlots           : 1

        NumPorts           : 50

        BaseMacAddr        : f8:15:47:e1:6f:00

        MacAddrCapacity    : 256

        System MTU         : 1950

Card Info :

        Slot#      CardType          Serial#            Part#             Oper   Admin  Power

                                                                        Status  Status  State

            1  4450GSX-PWR+     SDNIV50S1016               --               up      up     on

Temperature Info :

 Chassis Temperature

Installing the VSP 4450GSX-PWR+ series

August 2018

Installing the Virtual Services Platform 4450GSX-PWR+

38

Содержание EC4400004-E6














































Отзывы: