background image

21 

 

Set-up and Trimming

 

 
The CG range for the 3DHS 75" Edge 540 can be measured at the wing root and starts at  
4.75"-5.25" which closely correlates to the location of the wing tube.  If you balance at the 
center of the wing tube for the first flight you will be safe.  There is plenty of room on the 
battery tray to move your batteries to achieve this CG location. Depending on your flying 
style  you  can  adjust  the  position  of  the  battery  to  alter  the  CG  to  accommodate  your 
preferences.  
I  highly  recommend  fine  tuning  your  CG  using  the  45  degree  line  test.  Fly  the  aircraft 
from left to right or right to left, whichever direction you are more comfortable with at 3/4 
to  full  throttle.  Pull  the  aircraft  to  a  45  degree  up  line  and  establish  this  line  and 
immediately roll the aircraft inverted. Establish this line and let go of the elevator stick. 
Ideally the aircraft will continue  to track on that 45 degree  line for several hundred feet 
before  slowly  starting  to  level  off.  Adjust  the  position  of  your  batteries  to  achieve  this 
flight condition. Once satisfied with the location of your CG scribe a mark on the battery 
tray so that you can position the batteries in the same location each flight and achieve the 
same feel and flight characteristics each flight.  
 
I  also  highly  recommend  taking  the  time  to  properly  set  up  your  rates  and  exponential 
settings.  Setting  up  low  rates  for  precision  maneuvers  and  high  rates  for  aggressive 
aerobatics and 3D flight will allow you to experience the best attributes of the 3DHS Edge 
or  any aircraft for  that matter.  Here  are some  suggested rates to get started with. These 
are the rates and exponential values I feel comfortable with. If they feel awkward to you 
please adjust to your taste.  
 
Elevator: Low rate-8-10 degrees; 15-20% Exponential  
                3D rate-45-55 degrees; 40-50% Exponential  
                Insane tumble rate: As much as possible! 65-70% Exponential  
 
Rudder: Low rate-20 degrees; 45-50% Exponential  
               3D rate- As much as possible; 60-70% Exponential  
 
Aileron: Low rate-15-20%; 40-45% Exponential  
              3D rate- As much as possible; 50-60% Exponential 
 
 
 
 
 
 

Содержание 75" Edge 540 ARF























Отзывы: