background image

1

 

 

 

 

 

 

Thank  you  for  purchasing  this  8-line  Digital  I/O  to  Ethernet  Adapter 
(hereinafter  referred  to  as 

“Adapter”

).  It  is  designed  to  adopt  your 

digital I/O lines remotely on your Ethernet (Internet). It delivers simple, 
reliable  and  cost-effective  network  connectivity  for  your  digital  I/O 
applications such as home or industrial factory automation, digital I/O 
control  from  any  networked  PC,  alarm  and  power  monitoring  by 
network  or  Internet,  PC  controlled  machines,    distributed  machine 
I/O, remote lighting and power control etc. 

Features: 

 

4 Digital Input and 4 Output Lines over a 10-pin Terminal Blocks 

 

2 Non-inverted and 2 Inverted Output Lines 

 

Provides ESD and Surge Protection for all I/O Lines 

 

I/O Line Voltage is Compatible with CMOS/TTL 

 

Provides one 10/100Mbps, RJ45 LAN Port 

 

Provides TCP Server, TCP Client, and I/O Extender Modes 

 

P5VDC by DC Jack or Terminal Blocks 

 

Provides both Wall Mounting and DIN RAIL Kits 

 

Supports Virtual COM Port Drivers 

 

 
 
 

 

 

 

 

 
  
 

DIO Lines Terminal 
Blocks 

EX-6011 

8-line Digital I/O to Ethernet Adapter, w/ DIN 

RAIL Mounting Kit 

1. Introduction 

2. Connector Layout 

+5VDC Power 
Input DC Jack 

RJ45 LAN 
Connector 

Switch to Restore 
Default Settings   

Содержание EX-6011

























Отзывы: