6
5
1
Die EX
-
11494
-
3 ist eine USB 3.2 (Gen1) 4 Port Quad Channel PCI
-
Express Karte. Sie ist mit 4
externen Port
‘
s ausgestattet, die jeweils 900mA Strom zu Verfügung stellen. Sie unterstützt alle
PCI
-
Express Slots von x4 bis x16. Der serielle PCI
-
Express Bus unterstützt optimal die Leistung
des schnellen Renesas Chipsatz. Zusätzlich besitzt jeder einzelne USB 3.2 (Gen1) Port einen
eigenen Chip und somit auch einen eigenen Channel. Die EX
-
11494
-
3 gewährleistet so eine
sichere Datenübertragung und exzellente Performance von bis zu 5Gbit pro Sekunde an jedem
Port! Es wird empfohlen die EX
-
11494
-
3 mit zusätzlichen Strom vom PC Netzteil zu verbinden,
um die volle Leistung von 900mA an den 4 externen Port
‘
s zu gewährleisten.
ANSCHLÜSSE
J3
-
J6:
4x USB 3.2 (Gen1)
A
-
Buchse für Endgeräte
J1:
4 Pin Molex
Power Anschluss
vom PC
-
Netzteil
J2:
SATA 15 Pin
Power Anschluss
vom PC
-
Netzteil
AUFBAU
Anleitung
Vers. 1.1 / 28.07.2020
EX
-
11494
-
3
Kompatibilität:
PCI
-
Express x4 bis x16, USB 1.1, 2.0, 3.0 & 3.1
Betriebssysteme:
Windows XP/ Vista/ 7/ 8.x/ 10/Server 20xx/ Linux
Anschlüsse:
4x USB 3.2 (Gen1) A
-
Buchse, 1x 4 Pin Molex, 1x SATA 15 Pin
Lieferumfang:
EX
-
11494
-
3, Low Profile Bügel, Treiber CD, Anleitung
Zertifikate:
Achtung!
Stecker niemals umgekehrt
oder mit Gewalt einstecken.
USB 3.2 (Gen1) A
-
Buchse:
StdB_SS
StdB_SS
GND_DR
VCC
StdB_SS
StdB_SS
D+
D
-
GND
HARDWARE
INSTALLATION
CONNECTORS
DRIVER
INSTALLATION
J1:
J2:
Pin
Assignment
Pin
Assignment
Pin
Assignment
1
3.3 Volt (Orange)
7
5 Volt (pre
-
charge)
13
12 Volt (pre
-
charge)
2
3.3 Volt (Orange)
8
5 Volt (Red)
14
12 Volt (Yellow)
3
3.3 Volt (pre
-
charge)
9
5 Volt (Red)
15
12 Volt (Yellow)
4
Ground (Black)
10
Ground (Black)
5
Ground (Black)
11
Reserve
6
Ground (Black)
12
Ground (Black)
To guarantee the full 900mA at all ports of the EX
-
11494
-
3, it is recommended that the card be
connected with the power supply of the PC. It must be connected only one power connector J1
OR
J2!
Please make sure you connect the plug in the right direction.!
Never connect or release the plug while the PC is supplied with power!
1 +12V
2 GND
3 GND
4 +5V
To guarantee the full 900mA at all ports of the EX
-
11494
-
3,
it is recommended that the card be connected with the
power supply of the PC. It must be connected only one
power connector J1
OR
J2!
Please make sure you con-
nect the plug in the right direction!
Never connect or release the plug while the PC is
supplied with power!
Please note the following installation instructions. Because there are large differences between the
PC
’
s, we can give you only a general installation instructions for the EX
-
11494
-
3. Please refer your
computer
’
s reference manual whenever in doubt.
1.
Turn off the power to your computer and any other connected peripherals.
2.
Remove the mounting screws located at the rear and/or sides panels of your Computer and
gently slide the cover off.
3.
Locate an available PCI
-
Express expansion slot and insert the card. Make sure that the card
is plugged in correctly.
4.
Now install the power supply via the SATA 15 pin connector or the 4 pol molex connector.
(see picture Connectors J1 or J2)
5.
Then attach the card with a screw to the rear panel of the computer.
6.
Gently replace your computer
’
s cover and the mounting screws.
Windows XP/ Vista/ 7/ Server 2003 & 2008R2
After starting Windows is recognizes a new
“
USB (Universal Serial Bus)
-
Controller
“
.
Start the
„
SETUP
“
file which is in the
“
uPD720201_202
”
folder (see picture):
Follow the installation instructions and complete the installation.
Windows will now install automatically you right driver for your particular operating system. After
the installation the operating system detects the card and automatically install them.
CHECK INSTALLED DRIVER
Open the
>Device manager<.
Now you should see at
„
USB
-
Controller
“
the following new entry's:
If you see this or a similar information the device is installed correctly.
Windows 8.x/ 10/ Server 2012R2/ 2016/ 2019
After the hardware installation, the operating system will recognize the device automatically and
install the drivers.
CHECK INSTALLED DRIVER
Open the
>Device manager<.
Now you should see at
„
USB
-
Controller
“
the following new entry's:
If you see this or a similar information the device is installed correctly.
BESCHREIBUNG & TECHNISCHE DATEN
