Expert Electronics ColibriDDC Скачать руководство пользователя страница 66

Страница: 66 / 69

ColibriDDC User Manual

RECEIVER OPERATIONS

Synchronous t uning by t he click on t he bandscope.

Hover the mouse cursor on the required place on the bandscope and click left mouse button –

RX filter will move to the required location on both bandscope and panorama.

5.4

RIT

RIT offset means that signal receiving will be held on a frequency + Rit offset. Offset is

displayed as a translucent band on the spectrum scope. Tuned frequency displayed as the red

line. RX frequency displayed as the green line with the filter band (on the picture you can see

USB mode).

The following values will be displayed below the main receiver's frequency indicator:

RI T: - the frequency offset.

L: and H: - low and high filter's edges frequencies.

O: - mouse cursor frequency inside the filter.

To change the filter bandwidth: move the mouse cursor over the filter edge, it will be highlighted,

then drag the edge with the left mouse button.

When the RI T is enabled, frequency tuning changes a bit:

Press and hold the left mouse button inside the RX filter to move it over the panorama.

Press and hold the left right button inside the RX filter to move the whole panorama with the

filter.

Press and hold the middle mouse button inside the RX filter then move the mouse cursor out of

the filter bandwidth, the O: indicator will show the frequency difference between the mouse

cursor and the RX filter.

Note:

If the RIT offset wasn't reset, when you disable the RIT its state will be saved. When you
activate the RIT next time, the offset will equal the previous value.

Содержание ColibriDDC






































































Результаты поиска

Содержание ColibriDDC

Отзывы:

Бренды по названию

Популярные бренды

Expert Electronics ColibriDDC, Руководство пользователя

Результаты поиска

Содержание ColibriDDC

Отзывы:

Бренды по названию

Популярные бренды