Exmark Metro HP страница 32 Скачать руководство пользователя | Manualshive

Страница: 32 / 44

background image

- 27 -

FIG. 15

BLADE ENGAGEMENT LINKAGE

5.2.3

Blade Safety Switch: Mounted to a tab on the inside lefthand side of the fuel

tank support.

a)

Stop engine and remove spark plug wire(s).

b)

With blades disengaged and the bellcrank touching the rear of the slot in
the engine deck, adjust the blade safety switch (if needed) until the
bellcrank arm is 5/16” from the switch body.

c)

Be sure the bellcrank

DOES NOT

touch the switch body or damage to the

switch could occur.

d)

Retighten blade switch mounting hardware.

5.2.4

Engine to Cutter Deck Belt:

No adjustment necessary

.

5.2.5

Transmission Belt Adjustment:

a) Stop engine and remove spark plug wire(s).

b) To tighten transmission belt, loosen the 3/8” nyloc nut on transmission

belt idler pulley. Slide bolt inward in slot and retighten nyloc nut.

c) When properly adjusted, the belt should have 1/2” of deflection with three

pounds of pressure on the belt midway between the transmission and
engine pulley.

5.2.6

Wheel drive belts and scrapers:

a) If wheel traction appears to be slipping, drive lever rods may be touching

bottom of neutral lock/park brake latch slot. To adjust, refer to directions
in Section 3.11

NOTE: Wheel drive springs have three tension settings. Refer to Section
5.2.11.

b) Be sure mud and grass scraper, on each side, is adjusted properly and

centered in the pulley grooves. The pointed part of the scraper should be
centered and as deep in the pulley groove as possible without rubbing at
any point.

5.2.7 Brake Adjustment:

See 3.11

5.2.8 Wheel drive linkage adjustment:

See 3.11

5.2.9 Shifter lever adjustment:

See 3.10

5.2.10 Shifter detent adjustment:

Transmission shifter detent can be adjusted by adjusting the setscrew on the
backside of transmission located just behind the neutral start switch. Turn
setscrew in (clockwise) to hold the transmission shifter more positively in each
gear and to increase the force on the lever required to shift gears.

For Exmark Mower Parts Call 606-678-9623 or 606-561-4983

www.mymowerparts.com

«
...
30
31
32
33
34
...
»

Содержание Metro HP













































Отзывы:

Нет отзывов

Похожие инструкции для Metro HP

Бренд: Bad Boy Страницы: 46

Бренд: Meec tools Страницы: 30

Бренд: Stihl Страницы: 120

Бренд: AL-KO Страницы: 652

EXPERT 105.220 H

Бренд: Wolf Garten Страницы: 176

YARD-MAN Series 556

Бренд: Yard-Man Страницы: 20

Бренд: Ego Power+ Страницы: 176

Бренд: Bad Boy Страницы: 36

Бренд: Flymo Страницы: 10

Бренд: Nakayama Страницы: 80

Бренд: Brill Страницы: 104

Бренд: Cub Cadet Страницы: 1

Бренд: Cub Cadet Страницы: 2

Бренд: RC Mowers Страницы: 42

Бренд: Craftsman Страницы: 32

Craftsman 917.27576

Бренд: Craftsman Страницы: 34

Бренд: Craftsman Страницы: 31

Бренд: Craftsman Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды