Exhausto EXact2 VEX240 series Скачать руководство пользователя страница 52

Страница: 52 / 108

Example
Chiller

1358

6-01

Diagrams

See appendix 1 for VEX200 diagrams.

Menu 2.1.1 - Set points for regulators

2.1.1 Setp. regulators
Room

Heat recovery

Cooling unit

Heating unit

Compensation:

Outdoor temp.

Summer

0,0

10,0

Inactive

This menu shows set points for:

● Room temperature regulator
● Heat recovery regulator
● Cooling regulator
● Heating unit regulator

Compensations:

● List of compensations (active/inactive)

Menu 2.2 - Airflows

2.2 Airflows
Supply air

Supply air

Extract air

3150l/s

11340m³/h

3225l/s

11610m³/h

The menu shows the airflows (converted to airflows at 20°C) specified in l/s and
m

/h. Uncertainty for the measured airflow is less than ±8%.

Menu 2.3 - Motor controller parameters (MC parameters)

2.3 MC parameters

Supply air:

Maximum

Set point
Minimum

Extract air:
Maximum
Set point
Minimum

50.0Hz

30.0Hz
14.0Hz

50.0Hz
30.0Hz
14.0Hz

FC: The menu shows maximum and minimum frequencies. The set point shows
the frequency at the current ventilation level (e.g. 30 Hz).

3005167-2022-02-02

Operation

52/108

Содержание EXact2 VEX240 series













































































































Результаты поиска

Содержание EXact2 VEX240 series

Отзывы:

Похожие инструкции для EXact2 VEX240 series

Бренды по названию

Популярные бренды

Exhausto EXact2 VEX240 series, Основные инструкции

Результаты поиска

Содержание EXact2 VEX240 series

Отзывы:

Похожие инструкции для EXact2 VEX240 series

Бренды по названию

Популярные бренды