Exhausto EXact2 VEX240 series Скачать руководство пользователя страница 17

Страница: 17 / 108

Start configuration

Step

Action

Check that the correct configuration for the VEX/CX has been se-
lected at the factory via menu 3.3.

Check that all accessories have been configured in menu 3.4

If the CO

sensor has been mounted, check in menu 3.1.2.1 "CO

compensation", whether CO

compensation has been activated.

If the humidity sensor (RH sensor) has been installed, check that
humidity compensation has been activated in menu 3.1.2.2 "Hu-
midity compensation".

Go to menu 4.5 "Current list", and check whether any units from
the configuration menu are reporting errors. Alarm icon is shown in
the menu bar

If a unit is reporting an error but has been correctly configured,
check the installation.

3.3 Configuration
Type >

Size >

Fan positioning >

Direction >

Rotor type >

Cleaning zone >

200

Orientation

Right

Cond.

None

x50

Line in menu 3.3

Factory-set and

should not be

changed.

Remarks:

Type

Size

Fan location

Direction

Adjustable. See section se-
lecting Left/Right

Rotor type

Cleaning zone

3005167-2022-02-02

Starting up the unit for operation

17/108

Содержание EXact2 VEX240 series













































































































Результаты поиска

Содержание EXact2 VEX240 series

Отзывы:

Похожие инструкции для EXact2 VEX240 series

Бренды по названию

Популярные бренды

Exhausto EXact2 VEX240 series, Основные инструкции

Результаты поиска

Содержание EXact2 VEX240 series

Отзывы:

Похожие инструкции для EXact2 VEX240 series

Бренды по названию

Популярные бренды