EXFO Power Blazer 88200NGE Скачать руководство пользователя

Страница: 675 / 887

Test Functions

Power Blazer

665

OH - OTN



PSI

, column 15, OPU/ODU OH: Tap the PSI field to configure (TX) or

display (RX) the Payload Structure Identifier.



TX: Select any TX byte from the list and its content is displayed
below the list. Tap the

Edit

button to change its value.



RX: Select any RX byte from the list and its content is displayed
below the list.



Foreground Signal Label

: This is a legend representing the status

of the MSI for each PSI#, either

MSI TX

(black),

Expected MSI RX

(green), or

MSI Mismatch

(red).



The

Link TX/RX Scrolling

check box when selected (cleared by

default), allows synchronizing both TX and RX table allowing to
see the same TX and RX PSI byte numbers when scrolling from
either TX or RX table.



OMFI

NJO

OMFI

, column 16, OPU OH: OPU Multi-Frame Identifier is only

available for OPU4 of a mapped signal. This byte is not configurable.

NJO

, column 16, ODU OH: The Negative Justification Opportunity byte

is not configurable. Available either for non-concatenated signal or on
the LO of a concatenated signal.



RX OH Byte Details

displays the content of the selected OH RX byte.

Tap on any OH RX byte to see its content



Legend TX/RX

indicates the path level for all OH bytes.

Содержание Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Power Blazer 88200NGE

Отзывы:

Похожие инструкции для Power Blazer 88200NGE

Бренды по названию

Популярные бренды

EXFO Power Blazer 88200NGE, Руководство пользователя

Результаты поиска

Содержание Power Blazer 88200NGE

Отзывы:

Похожие инструкции для Power Blazer 88200NGE

Бренды по названию

Популярные бренды