EXFO Power Blazer 88200NGE Скачать руководство пользователя

Страница: 434 / 887

Test Results

424

88000 Series

Alarms/Errors Overview

GMP and ODTU4.x - GMP (Generic Mapping
Procedure)

Note:

GMP is only available with EoOTN client (ODU0 with PT21). GMP is
displayed under ODUx alarms/errors group.

GMP

is labelled as

ODTU4.1 - GMP

with Multi-Channel OTN and

ODTUC4.80 - GMP

with

FlexO BERT.

Alarms



OOS

(Generic Mapping Procedure - Out Of Synchronization).

: Indicates that the GMP RX cannot synchronize with the GMP TX.

Errors



Cm-CRC-8

: There is a Cm-CRC-8 mismatch between the received value and

the locally computed value.



CnD-CRC-5

: There is a CnD-CRC-5 mismatch between the received value and

the locally computed value.



Cm-CRC-6

: There is a Cm-CRC-6 mismatch between the received value and

the locally computed value.



CnD-CRC-9

: There is a CnD-CRC-9 mismatch between the received value and

the locally computed value.

Содержание Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Power Blazer 88200NGE

Отзывы:

Похожие инструкции для Power Blazer 88200NGE

Бренды по названию

Популярные бренды

EXFO Power Blazer 88200NGE, Руководство пользователя

Результаты поиска

Содержание Power Blazer 88200NGE

Отзывы:

Похожие инструкции для Power Blazer 88200NGE

Бренды по названию

Популярные бренды