EXFO Power Blazer 88200NGE Скачать руководство пользователя

Страница: 417 / 887

Test Results

Power Blazer

407

Alarms/Errors Overview



Oversize

(available when the

Oversize Monitoring

check box is

selected.)

: Frames larger than 1518 bytes

with a valid FCS; 1534 bytes

for

EoE; 1536 bytes

for PBB-TE.



Runt

: Frames smaller than 64 bytes with an invalid FCS; 80 bytes for EoE;

82 bytes for PBB-TE.



Undersize

: Frames smaller than 64 bytes with a valid FCS; 80 bytes for EoE; 82

bytes for PBB-TE.



Oversize Monitoring

check box, when selected (cleared by default),

allows monitoring the

Oversize

frame errors.

The following errors are only available with

Half Duplex

mode (only for

electrical interface at speeds of 10 Mbit/s and 100 Mbit/s).



Collision

: Indicates the number of collisions on the link.



Late Coll.

: Indicates the number of collisions that have occurred after a 64

bytes transmission.



Exc. Coll.

: Indicates the number of frames that were sent 16 times

unsuccessfully due to consecutive collisions.

Содержание Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Power Blazer 88200NGE

Отзывы:

Похожие инструкции для Power Blazer 88200NGE

Бренды по названию

Популярные бренды

EXFO Power Blazer 88200NGE, Руководство пользователя

Результаты поиска

Содержание Power Blazer 88200NGE

Отзывы:

Похожие инструкции для Power Blazer 88200NGE

Бренды по названию

Популярные бренды