EXFO Power Blazer 88200NGE Скачать руководство пользователя

Страница: 269 / 887

Test Setup - Test Configurator, Timer, and System

Power Blazer

259

MAC/IP/UDP



Prefix Mask

, available with

Static

mode, allows specifying a prefix

that defines the subnet. The accepted range is

0000:0000:0000:0000:0000:0000:0000:0000

FFFF:FFFF:FFFF:FFFF:0000:0000:0000:0000

. For example:

Global Address: 2001:0DB8:0001:0002:02AA:00FF:FE11:1111
Prefix Mask: FFFF:FFFF:FFFF:0000:0000:0000:0000:0000
Corresponding Prefix: 2001:0DB8:0001.



Default Gateway

allows the configuration of the default gateway

address to forward packets outside the subnet.



Mode

Automatic

(default) allows automatic selection of the default

gateway.

Static

allows entering the default gateway IP address.



Address

, available with

Static

mode, allows entering the IP

address of the Default Gateway. The accepted range is from

0000:0000:0000:0000:0000:0000:0000:0000

FE80:0000:0000:0000:FFFF:FFFF:FFFF:FFFF

. The default address

FE80:0000:0000:0000:0000:0000:0000:0000



IPv6 Destination Address

allows selecting the destination IP address

for the stream that must start with

FE80

. The accepted range is from

0000:0000:0000:0000:0000:0000:0000:0001

FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF:FFFF.

The default address is

2001::

. When the

Address

field is selected for editing using virtual

keyboard, the

Previous IPs

button appears allowing the selection of a

previously configured IP address.

Содержание Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Power Blazer 88200NGE

Отзывы:

Похожие инструкции для Power Blazer 88200NGE

Бренды по названию

Популярные бренды

EXFO Power Blazer 88200NGE, Руководство пользователя

Результаты поиска

Содержание Power Blazer 88200NGE

Отзывы:

Похожие инструкции для Power Blazer 88200NGE

Бренды по названию

Популярные бренды