EXFO Power Blazer 88200NGE Скачать руководство пользователя | Manualshive

Страница: 267 / 887

background image

Test Setup - Test Configurator, Timer, and System

Power Blazer

257

MAC/IP/UDP

IP

For

IPv4

the following configuration parameters are available.



Automatic IP (DHCP)

check box, when selected (cleared by default),

allows obtaining an IP address dynamically from a DHCP (Dynamic
Host Configuration Protocol) server.



Source IP Address

allows entering the source IP address for the

stream. The default setting is 10.10.x.y, where x and y are respectively
the two least significant bytes of the port default MAC address. Not
available when the

Automatic IP (DHCP)

check box is selected.



Destination IP Address

allows entering the destination IP address for

the stream. The default setting is the source IP address.

For

IPv6

the following configuration parameters are displayed:

Source

Link-Local IPv6 Address

, and

Source Global IPv6 Address

. Tap on the

IPv6 Config

button to access all settings.



Link-Local IPv6 Address

(LLA) is used for local communication

between on-link neighbors and for Neighbor Discovery process.



Mode

Stateless Auto

(default) allows automatic generation of the IPv6

address based on the MAC address.

Static

allows entering the IP Address.



Address

, available with

Static

mode, allows selecting the

Link-Local IPv6 Address. The accepted range is from

FE80:0000:0000:0000:0000:0000:0000:0000

to

FE80:0000:0000:0000:FFFF:FFFF:FFFF:FFFF.

The default address

is

FE80::[Interface ID]

, where [

Interface ID

] is generated from

the source MAC address. When the

Address

field is selected for

editing using virtual keyboard, the

Previous IPs

button appears

allowing the selection of a previously configured IP address.

«
...
265
266
267
268
269
...
»

Содержание Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88200NGE

Бренд: Bard Страницы: 8

Бренд: Bardiani Valvole Страницы: 35

Бренд: Danfoss Страницы: 85

VLT Decentral FCD 300

Бренд: Danfoss Страницы: 112

Бренд: Danfoss Страницы: 4

VLT 6000 series

Бренд: Danfoss Страницы: 27

Бренд: Danfoss Страницы: 16

Бренд: Danfoss Страницы: 20

ADAP-KOOL AK-PC 781

Бренд: Danfoss Страницы: 14

Бренд: Danfoss Страницы: 12

vlt soft starter mcd 500

Бренд: Danfoss Страницы: 96

Бренд: Warren Controls Страницы: 28

Бренд: EAS Electric Страницы: 89

Бренд: Uclear Страницы: 40

Бренд: U-Prox Страницы: 3

Бренд: U-Prox Страницы: 2

Бренд: Waterway Страницы: 8

Бренд: Aurora Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды