EXFO Power Blazer 88200NGE Скачать руководство пользователя | Manualshive

Страница: 244 / 887

background image

Test Setup - Test Configurator, Timer, and System

234

88000 Series

Interface



Min RX Power (dBm)

indicates, when supported, the minimum

received power level of the optical laser/lane in dBm.



Max RX Power (dBm)

indicates, when supported, the maximum

received power level of the optical laser/lane in dBm.



Laser ON/OFF

button, available with parallel interfaces, is used to

activate the laser control per optical lane or for all lanes.

Optical lane numbers are from

0

to

3

or

0

to

7

depending on the

selected interface/rate.



All Lanes

check box, when selected, applies the change(s) to all

optical lanes at once.



Optical Lane

indicates the optical lane numbers and

All

which

represents the setting for all optical lanes when the

All Lanes

check box is selected.



Laser

check box, when selected, indicates that the corresponding

optical laser lane is activated and emitting an optical laser signal.



Laser OFF at Start-Up

check box when selected, cleared by default,

automatically turns OFF the laser for serial interfaces or all lasers for
parallel interfaces when starting the module or when switching from
one test application to another; this applies on both ports for

Dual Port

topology. However the laser remains ON, on a remote module
receiving a request for a DTS connection or a loopback command.

«
...
242
243
244
245
246
...
»

Содержание Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88200NGE

Бренд: NEJE Страницы: 17

Бренд: Oceanic Страницы: 13

Бренд: QUAD Страницы: 16

Бренд: Panasonic Страницы: 27

Бренд: Panasonic Страницы: 78

Бренд: Panasonic Страницы: 98

Бренд: NAiS Страницы: 173

Бренд: Panasonic Страницы: 2

Бренд: Dantherm Страницы: 96

Бренд: Barthelme Страницы: 8

Бренд: CAB Страницы: 28

Бренд: C-TEC Страницы: 16

Бренд: C&T Solution Страницы: 27

SECURIT ST800L+

Бренд: C&K systems Страницы: 16

Бренд: Campbell Страницы: 8

Бренд: Campbell Страницы: 3

Бренд: hager Страницы: 62

coviva Smartbox TKP100A

Бренд: hager Страницы: 45

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды