EXFO Power Blazer 88200NGE Скачать руководство пользователя

Страница: 227 / 887

Test Setup - Test Configurator, Timer, and System

Power Blazer

217

FTFL/PT and PT

FTFL/PT and PT

For OTN BERT and OTN-SONET/SDH BERT: From the

Test

menu tap

Setup

Test Configurator

, tap on the interface block, and on the

FTFL/PT

tab.

For Multi-Channel OTN: From the

Test

menu, tap

Setup

Test

Configurator

, tap on either:



the interface block, and on the

tab to configure the higher ODU

layer.



the test block (

ODU Channels

), and on the

tab to configure the

lower ODU layer.

ODUx Buttons

Tap on an

ODUx

button to select the multiplexed level. Not available with

Multi-Channel OTN lower ODU level.

Содержание Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Power Blazer 88200NGE

Отзывы:

Похожие инструкции для Power Blazer 88200NGE

Бренды по названию

Популярные бренды

EXFO Power Blazer 88200NGE, Руководство пользователя

Результаты поиска

Содержание Power Blazer 88200NGE

Отзывы:

Похожие инструкции для Power Blazer 88200NGE

Бренды по названию

Популярные бренды