EXFO Power Blazer 88200NGE Скачать руководство пользователя

Страница: 179 / 887

Test Setup - Test Configurator, Timer, and System

Power Blazer

169

Clock



Termination

mode specifies how the module is connected to the

synchronization signal. The

Termination

mode is set to

TERM

for 2MHz

and configurable for DS1 and E1.

For DS1:



TERM

provides an input that terminates the DS1 signal.



DSX-MON

provides high-input impedance and compensation for

resistive loss. This setting is useful for monitoring DS1 signals at
DSX monitor points, which are resistor-isolated.



BRIDGE

provides high-input impedance for bridging lines that are

already terminated. This setting is useful for bridging directly
across copper cable pairs.

For E1:



TERM

provides an input that terminates the E1 signal.



MON

provides high-input impedance and compensation for

resistive loss. This setting is useful for monitoring E1 signals at
monitor points, which are resistor-isolated.



BRIDGE

provides high-input impedance for bridging lines that are

already terminated. This setting is useful for bridging directly
across copper cable pairs.



Line Coding

allows the selection of the interface line coding.

For DS1:

AMI

and

B8ZS

(default).

For E1:

AMI

and

HDB3

(default).



Framing

: Allows the selection of the interface framing.

For DS1:

SLC-96

, and

ESF

(default).

For E1:

PCM30

(default),

PCM30 CRC-4

PCM31

, and

PCM31 CRC-4



Frequency (MHz)

displays the frequency of the received signal rate.

Содержание Power Blazer 88200NGE
























































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Power Blazer 88200NGE

Отзывы:

Похожие инструкции для Power Blazer 88200NGE

Бренды по названию

Популярные бренды

EXFO Power Blazer 88200NGE, Руководство пользователя

Результаты поиска

Содержание Power Blazer 88200NGE

Отзывы:

Похожие инструкции для Power Blazer 88200NGE

Бренды по названию

Популярные бренды