EXFO Power Blazer 88000 Series Скачать руководство пользователя | Manualshive

Страница: 676 / 803

background image

Maintenance

664

88000 Series

Cleaning LC/SC/MPO-24 Connectors

Cleaning LC/SC/MPO-24 Connectors

Under normal circumstances the cleaning of the LC/SC/MPO-24 connector
is not required. However if the connector shows signs of debris or
contamination, cleaning may be required.

To clean a LC/SC/MPO-24 connector
1.

Use a clean dry air (CDA) or a air gun to blow out the dust or
contamination.

2.

Re-inspect the connector. For MPO-24 optical connector, re-inspect the
connector under magnification to make sure that it is clean.

3.

If the connector is still not clean, use a commercial cleaner
recommended by the transceiver manufacturer.

Note:

Refer to the transceiver manufacturer for more detailed cleaning
recommendations and instructions.

Battery Safety Information

The TA-... modules contain a battery for the insertion counter. If the battery
status is low, contact your nearest authorized EXFO service center for its
replacement.

W

ARNING

Do not throw batteries into fire or water and do not short-circuit
the batteries’ electrical contacts. Do not disassemble.

«
...
674
675
676
677
678
...
»

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88000 Series

Бренд: Samson Страницы: 78

Бренд: Rachio Страницы: 16

Бренд: Banner Страницы: 15

Бренд: bar Страницы: 2

Бренд: Rabbit Страницы: 38

Бренд: GBD Страницы: 60

Бренд: Samson Страницы: 102

Бренд: Game ready Страницы: 24

Бренд: SMC Networks Страницы: 10

Бренд: Riello Страницы: 72

Controller CR100

Бренд: Sonos Страницы: 2

Бренд: Midland Страницы: 37

Бренд: Sensitron Страницы: 32

Serial Interface Module

Бренд: Federal Signal Corporation Страницы: 12

Бренд: Phoenix Contact Страницы: 40

Бренд: MERCATOR Страницы: 4

Бренд: W&T Страницы: 217

Бренд: Consort Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды