EXFO Power Blazer 88000 Series Скачать руководство пользователя

Страница: 602 / 803

Test Functions

590

88000 Series

OH - OTN



RES

, column 9-14, ODU OH: The six Reserved (RES) bytes are

configurable from

(default for each byte) to



PSI

, column 15, OPU/ODU OH: Tap the PSI field to configure (TX) or

display (RX) the Payload Structure Identifier.



TX: Select any TX byte from the list and its content is displayed
below the list. Tap the

Edit

button to change its value.



RX: Select any RX byte from the list and its content is displayed
below the list.



Link TX/RX Scrolling

, when selected (cleared by default), allows

synchronizing both TX and RX table allowing to see the same TX
and RX PSI byte numbers when scrolling from either TX or RX
table.



Foreground Signal Label

: Indicates the status of the MSI for each

PSI#, either

MSI TX

(black),

Expected MSI RX

(green), or

MSI

Mismatch

(red).



OMFI

NJO

OMFI

, column 16, OPU OH: OPU Multi-Frame Identifier is only

available for OPU4 of a mapped signal. This byte is not configurable.

NJO

, column 16, ODU OH: The Negative Justification Opportunity byte

is not configurable. Available either for non-concatenated signal or on
the LO of a concatenated signal.



RX OH Byte Details

displays the content of the selected OH RX byte.

Tap on any OH RX byte to see its content



Legend TX/RX

indicates the path level for all OH bytes.

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Power Blazer 88000 Series

Отзывы:

Похожие инструкции для Power Blazer 88000 Series

Бренды по названию

Популярные бренды

EXFO Power Blazer 88000 Series, Руководство пользователя

Результаты поиска

Содержание Power Blazer 88000 Series

Отзывы:

Похожие инструкции для Power Blazer 88000 Series

Бренды по названию

Популярные бренды