manualshive.com logo in svg

EXFO Power Blazer 88000 Series, Руководство пользователя, Страница: 591 / 803

Поделиться
Скачать
EXFO Power Blazer 88000 Series Скачать руководство пользователя страница 591

Test Functions

Power Blazer

579

GMP

GMP 

Note:

Available with Transport test applications with either payload type 21 
(PT21) or one of the following clients: 

1GbE

, 

40GbE

, 

100GbE

, 

Ethernet 

(flex/GFP-F)

, or SONET/SDH (through ODU0). 

From the

 Test

 menu, tap 

Functions

, and the 

GMP

 tab. 

Channel

Available with Multi-Channel OTN, allows the selection of the channel 
number. 

Generic Mapping Procedure

TX Cm

 indicates the minimum and maximum Cm value transmitted 

during the test. 

TX CnD

 indicates the minimum and maximum CnD value transmitted 

during the test. 

RX Cm

 indicates the minimum and maximum Cm value captured 

during the test. 

RX CnD

 indicates the minimum and maximum CnD value captured 

during the test. 

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов