EXFO Power Blazer 88000 Series Скачать руководство пользователя | Manualshive

Страница: 487 / 803

background image

Test Results

Power Blazer

475

Summary (1588 PTP)



Negotiation Status

The status of the PTP Negotiation is displayed while in Unicast
negotiation (available with G.8265.1 profile).

Negotiation

Status

Description

Background

Color

a

a.

The gray background color is also used for a Link Down.

Request Granted

All the Signaling request types have been granted.

Green

[Message type]

Request Denied

The Signaling grant message has not been granted.

Red

Session Canceled

The Grand Master has canceled the Unicast session.

Red

No Reply

No message is received from the Grand Master following
transmission of 3 Signaling requests for a message type.
Make sure that both IP address and Domain (refer to

page 132) of the Grand Master Clock are valid as well as the IP
address of the unit’s port used to connect on the network (refer to

Red

Pending

Unicast negotiation has started and no message has been received
from the Grand Master.

Gray

Inactive

The Unicast negotiation is not active.

Gray

«
...
485
486
487
488
489
...
»

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88000 Series

615 Series ANSI

Бренд: ABB Страницы: 60

Бренд: S&C Страницы: 40

Бренд: S&C Страницы: 34

Бренд: Parker Страницы: 30

Бренд: VAT Страницы: 22

Бренд: Walchem Страницы: 10

Бренд: Taie Страницы: 28

Бренд: IFM Страницы: 49

Бренд: Jedia Страницы: 12

Бренд: JED Micro Страницы: 10

Бренд: JCM Technologies Страницы: 2

Бренд: Paradox Страницы: 2

Бренд: Parkside Страницы: 86

Бренд: RADEMACHER Страницы: 68

Бренд: National Instruments Страницы: 72

Бренд: National Instruments Страницы: 41

MAGNUM ALERT 3000 FIRE ALARM

Бренд: NAPCO Страницы: 2

Бренд: Ultraflex Страницы: 7

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды