EXFO Power Blazer 88000 Series Скачать руководство пользователя | Manualshive

Страница: 454 / 803

background image

Test Results

442

88000 Series

Performance Monitoring



UAS

(Unavailable Second): Gives the count of the seconds

corresponding to the periods of unavailable time that begins at the
onset of 10 consecutive SES events, including these 10 seconds. A
period of available time shall begin at the onset of 10 consecutive
non-SES events, including these 10 seconds.



ESR

(Errored Second Ratio) (

G.821

,

G.826

,

G.828

, and

G.829

): Gives

the ratio of the number of ES in available time (AS) during a fixed
measurement interval.

ESR = ES ÷ AS



SESR

(Severely Errored Second Ratio) (

G.821

,

G.826

,

G.828

, and

G.829

): Gives the ratio of the number of SES in available time (AS)

during a fixed measurement interval.

SESR = SES ÷ AS



BBER

(Background Block Error Ratio) (

G.826

,

G.828

,

G.829

, and

M.2101

): Gives the ratio of BBE in available time (AS) to total blocks in

available time during a fixed measurement interval. The count of total
blocks excludes all blocks during SESs.



DM

(Degraded Minutes) (

G.821

only): A Degraded Minute is the

number of minutes in which the estimated error rate exceeds 10

-6

but

does not exceed 10

-3

. DM is determined by collecting all of the

Available Seconds, removing any SES grouping the result in 60-second
long groups and counting a 60-second long group as degraded if the
cumulative errors during the seconds present in the group exceed 10

-6

.

«
...
452
453
454
455
456
...
»

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88000 Series

Бренд: Warner Electric Страницы: 3

Бренд: iCeeO2 Страницы: 7

Бренд: SABAF Страницы: 6

Бренд: GE Страницы: 425

Бренд: Harman Kardon Страницы: 25

Бренд: Uniss Страницы: 21

SIGMA CONTROL 2

Бренд: KAESER KOMPRESSOREN Страницы: 246

Бренд: Paradox Страницы: 2

Бренд: Paradox Страницы: 44

Бренд: UNICORECOMM Страницы: 32

Бренд: UNICORECOMM Страницы: 7

Бренд: UNICORECOMM Страницы: 26

Бренд: UNICORECOMM Страницы: 25

Ambience Control 1

Бренд: EuroLite Страницы: 20

Бренд: SKF Страницы: 88

Бренд: Velux Страницы: 11

Бренд: Kantronics Страницы: 201

Бренд: Simpnic Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды