EXFO Power Blazer 88000 Series Скачать руководство пользователя

Страница: 448 / 803

Test Results

436

88000 Series

MPLS

MPLS

For

Traffic Gen and Mon

, from the test menu, tap

Results

Streams

, and

the

MPLS

tab.

For

Though Mode

, from the test menu, tap

Results

Traffic

, and the

MPLS

tab.

Note:

For

Dual Port

topology, the P1 and P2 buttons allow respectively displaying

results for port #1 (

) or port #2 (

Label 1 and Label 2

The number of MPLS frames transmitted (TX) and received (RX) are
displayed for both

Label 1

and

Label

2 for each

Stream

. Not available for

Through Mode

test application.

Total TX/RX MPLS



Line Utilization

indicates the percentage of MPLS line rate utilization

in TX and RX.



Ethernet BW (%)

(Ethernet Bandwidth) indicates the MPLS data rate

in TX and RX.



Frame Rate (frames/s)

indicates the number of transmitted (TX) and

received (RX) MPLS frames).



Frame Count

indicates the count of transmitted (TX) and received

(RX) MPLS EtherType (0x8847 or 0x8848) frames regardless if FCS is
good or not.

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Power Blazer 88000 Series

Отзывы:

Похожие инструкции для Power Blazer 88000 Series

Бренды по названию

Популярные бренды

EXFO Power Blazer 88000 Series, Руководство пользователя

Результаты поиска

Содержание Power Blazer 88000 Series

Отзывы:

Похожие инструкции для Power Blazer 88000 Series

Бренды по названию

Популярные бренды