EXFO Power Blazer 88000 Series Скачать руководство пользователя

Страница: 389 / 803

Test Results

Power Blazer

377

Alarms/Errors Overview

OBSAI

Note:

OBSAI alarms/errors are only available for Framed L2.

Alarms



Link Down

: Indicates that the RX state machine is not FRAME_SYNC.



LOF

(Loss Of Frame)

: The RX state machine is in either WAIT_FOR_K28.7_IDLES or

SCR_CAP state.



RP3 Address Mismatch

available when

Address Mismatch

is enabled

(refer to page 190)

: Indicates that the RP3 Target Address does not match the local RP3

Source Address.

Errors



FAS

(Frame Alignment Signal)

: Error detected in message group terminating character (byte

different of K28.5) or master frame terminating character (byte
different of K28.7).



CRC

(Cyclic Redundancy Check)

: Indicates a message received with an invalid CRC.

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Power Blazer 88000 Series

Отзывы:

Похожие инструкции для Power Blazer 88000 Series

Бренды по названию

Популярные бренды

EXFO Power Blazer 88000 Series, Руководство пользователя

Результаты поиска

Содержание Power Blazer 88000 Series

Отзывы:

Похожие инструкции для Power Blazer 88000 Series

Бренды по названию

Популярные бренды