EXFO Power Blazer 88000 Series Скачать руководство пользователя | Manualshive

Страница: 342 / 803

background image

Test Setup - Test Configurator, Timer, and System

330

88000 Series

Timer

Timer

Allows starting and/or stopping automatically the test at a given time or for
a specific duration.

From the

Test

menu, tap

Setup

, and

Timer

.

Timer

Note:

For RFC 2544 and RFC 6349, only

Start Time

and the

ARM

button are

available.



Duration

: Selects the test duration based on the test start time. The test

start time can be either the time the user starts the test or the time the
test is automatically started when the start time is enabled. The

Duration

check box has to be selected to be included in the test timer.

Choices are

15 minutes

(default),

1

,

2

,

4

,

6

,

12

,

24

,

72 hours

,

7 days

,

and

User Defined

.

When

User Defined

is selected, the field next to it becomes available

to enter the test duration using the format: dd:hh:mm:ss.

Note:

Duration cannot be enabled while stop time is enabled. When the test is
started while duration is enabled, the stop time is calculated and the Stop
Time field is updated to indicate the time the test will stop.



Start Time

selects the time the test will automatically start. The

Start

Time

check box has to be selected to be included in the test timer.

Note:

A valid start time has to be subsequent to the current time.

«
...
340
341
342
343
344
...
»

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88000 Series

Бренд: ABB Страницы: 138

Бренд: ABB Страницы: 116

Relion 615 series

Бренд: ABB Страницы: 136

Leroy-Somer R180

Бренд: Nidec Страницы: 20

Бренд: TCS Basys Controls Страницы: 2

Бренд: jcm-tech Страницы: 8

Бренд: National Instruments Страницы: 72

Бренд: National Instruments Страницы: 41

MAGNUM ALERT 3000 FIRE ALARM

Бренд: NAPCO Страницы: 2

Бренд: GEA Страницы: 13

Бренд: Reliance Foundry Страницы: 3

Бренд: Wesa Страницы: 8

Liquitron DP5000-01A

Бренд: LMI Technologies Страницы: 28

Бренд: Motrona Страницы: 10

PSS67 IO1 16FDI

Бренд: Pilz Страницы: 36

ZoneSense Plus AS

Бренд: Halma Страницы: 58

VBA-2E-G11-I/U/PT100-F

Бренд: Pepperl+Fuchs Страницы: 24

NovoCon S Digital

Бренд: Danfoss Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды