EXFO Power Blazer 88000 Series Скачать руководство пользователя

Страница: 284 / 803

Test Setup - Test Configurator, Timer, and System

272

88000 Series

S-OAM and MPLS-TP OAM



Drop Eligible

, available with S-OAM Mode or when VLAN is enabled

(see

VLAN

on page 225), is set to

(no frames will be dropped when

congestion occurs) and is not configurable.



Period

determines the transmission period of the CCM frame:

3.33 ms

10 ms

100 ms

(default),

1 s

10 s

1 min

, or

10 min

MPLS-TP Label Stack (G.8113.1)



MPLS-TP Mode

(Pseudo-Wire) (default) provides an emulation of a point-to-point

connection over a packet-switching network. The PW begins and ends
at the LER or PE (Provider Edge).

LSP

(Label Switch Path) is a path through a MPLS network, it begins

and ends at LER or LSR.

Section

is a segment between two adjacent LER/LSR.



Label 2

check box when selected enables the MPLS Label 2. The

Label 2 check box is configurable for PW and LSP (cleared by default)
and is forced cleared for Section.



Label 1

check box when selected enables the MPLS Label 1.

The

Label 1

check box is forced selected for PW and LSP and forced

cleared for Section.



GAL

check box when selected enables the Generic Associated

Channel Label. The GAL check box is forced selected for LSP and
Section and is configurable for PW (selected by default).



Label

is configurable for

Label 1

and

Label 2

1048575

, default

. Label is not configurable for GAL and is set to



sets the Traffic Class:

(default) to



TTL

sets the Time To Live:

255

, default is

128

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Power Blazer 88000 Series

Отзывы:

Похожие инструкции для Power Blazer 88000 Series

Бренды по названию

Популярные бренды

EXFO Power Blazer 88000 Series, Руководство пользователя

Результаты поиска

Содержание Power Blazer 88000 Series

Отзывы:

Похожие инструкции для Power Blazer 88000 Series

Бренды по названию

Популярные бренды