EXFO Power Blazer 88000 Series Скачать руководство пользователя | Manualshive

Страница: 238 / 803

background image

Test Setup - Test Configurator, Timer, and System

226

88000 Series

Network Details (iSAM)

Network Details (iSAM)

Either select the Layer parameter, the number of services, for each service
the profile and CIR settings, or click on

More

for all settings.

The total bandwidth (when the

Performance Test

is enabled) and the

estimated test duration are also displayed.

NAT LAN/WAN

indicate presence of NAT (Network Address Translation)

router. The NAT router is automatically detected and graphically displayed
with LAN/WAN indication.

Note:

When there is a NAT at the Remote site, it is required to create UDP/TCP
port 62819 forwarding rule on this NAT router to allow DTS communication.
In addition, when there is a NAT in both directions (L->R and R->L), it is
required to create port forwarding rules on the NAT router located at the
Remote side for UDP port 7.

From the

Test

menu, tap

Setup

,

Test Configurator

, and the

More

button

from the

Network

block.

iSAM



Layer

is the layer used for all services. The layer is fixed to

L3/L4

when

the

RFC 6349 Test

is enabled.



L2

(default) for Ethernet II.



L3/L4

for Ethernet II, IP (IPv4), and respectively UDP for the

Configuration and Performance subtests, and TCP for RFC-6349
subtest.



Classification

defines the traffic classification used in the provider

network:

VLAN ID

,

VLAN Priority

, or

DSCP

(available with layer L3/L4).

Note:

At least one check box (

Configuration Test

, or

Performance Test

, or

RFC 6349 Test

) has to be selected.

«
...
236
237
238
239
240
...
»

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88000 Series

Бренд: Jafar Страницы: 9

Бренд: Nelson Страницы: 19

Бренд: C-TEC Страницы: 2

Бренд: Gantner Страницы: 56

Бренд: Waterway Страницы: 16

Бренд: Bang & Olufsen Страницы: 9

Бренд: Bang & Olufsen Страницы: 12

Бренд: Hach Страницы: 86

Бренд: B&G Страницы: 2

Бренд: B&K Страницы: 9

Бренд: Manfrotto Страницы: 16

Бренд: Campbell Страницы: 8

Бренд: Veeder-Root Страницы: 27

Бренд: Valve Concepts Страницы: 18

Бренд: K&K Страницы: 6

Бренд: ZKTeco Страницы: 6

Бренд: Hattersley Страницы: 2

Бренд: National Instruments Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды