EXFO Power Blazer 88000 Series Скачать руководство пользователя | Manualshive

Страница: 157 / 803

background image

Test Setup - Test Configurator, Timer, and System

Power Blazer

145

Cable Test

Cable Test

From the

Test

menu, tap

Setup

,

Test Configurator

, and the test block.

Global Options



Wiring Standard

is the pin-to-pair assignment corresponding to the

UTP cable used:

T568A

(default) or

T568B

.



Length Unit

is the unit used for cable length and distance to fault

results:

Meter

(default) or

Feet

.



PoE

check box when selected (cleared by default) allows verifying that

the Power Sourcing Equipment (PSE) is capable to deliver appropriate
power (PoE) to the Powered Device (PD). The PoE test is performed
after the cable test is executed confirming that the cable is ready to
carry data and power: either the Wire Map test reported

No fault

,

Straight pair

,

Crossed Pair

, or

Noise (link up)

. Only available on

8870/8880.

«
...
155
156
157
158
159
...
»

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88000 Series

Бренд: Parasound Страницы: 72

Бренд: Jafar Страницы: 15

Бренд: Calpeda Страницы: 4

Бренд: HABONIM Страницы: 9

Бренд: Federal Signal Corporation Страницы: 34

ROBO Cylinder RCP2 Series

Бренд: IAI Страницы: 5

Бренд: B&G Страницы: 19

Бренд: Nordelettronica Страницы: 8

Бренд: Danfoss Страницы: 16

Consolidated 2900-40 Series

Бренд: Baker Hughes Страницы: 80

Бренд: Advantech Страницы: 2

Vizia RF+ VRP15-1LW

Бренд: Leviton Страницы: 3

Бренд: Bentel Страницы: 88

Бренд: Zenith Страницы: 20

Бренд: Elfa Страницы: 22

Бренд: Tripp Lite Страницы: 40

Бренд: Texas Instruments Страницы: 25

Бренд: Yoshitake Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды