EXFO Power Blazer 88000 Series Скачать руководство пользователя | Manualshive

Страница: 103 / 803

background image

Selecting and Starting a Test

Power Blazer

91

Fibre Channel Test Application

Fibre Channel Test Application

To select, configure, and start a Fibre Channel test:
1.

From the test menu, tap

Setup

.

2.

From the

Test Applications

tab, under

Fibre Channel

, tap the

FC BERT

test icon.

3.

From the

Test Configurator

tab configure the interface structure and

its parameters.

3a.

Tap the

Modify

Structure

button to set the basic structure of the

test such as the interface/rate and connector. (refer to

Structure Button

3b.

Tap the interface block to configure the interface parameters
(refer to page 182). Ensure that the link is up and the power level
(when supported) is present in the status bar before proceeding
to the next step (refer to

3c.

Tap the protocol block to configure the frame structure and its
parameters (refer to page 172).

Modify Structure

Protocol Block

Test Block

Clock Block

Interface Block

Physical

Interface Port

«
...
101
102
103
104
105
...
»

Содержание Power Blazer 88000 Series




































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Power Blazer 88000 Series

Бренд: Eaton Страницы: 16

7000-2 - Escalade RAID Controller

Бренд: 3Ware Страницы: 2

Бренд: Zeagle Страницы: 37

Бренд: Garmin Страницы: 4

Бренд: Sanhua Страницы: 3

Бренд: Pando Страницы: 43

Бренд: IDTECK Страницы: 12

Бренд: Banner Страницы: 2

CGLine+ Web Controller

Бренд: Eaton Страницы: 28

Бренд: Vag Страницы: 12

Бренд: Linear Technology Страницы: 7

J1000 CIMR-JC series

Бренд: YASKAWA Страницы: 25

CIATControl OPC Server

Бренд: CIAT Страницы: 32

Бренд: Danfoss Страницы: 8

Infi 90 IMAOM01

Бренд: Bailey Страницы: 44

Бренд: Victaulic Страницы: 2

MU System X Dual Amplifier

Бренд: Frequency Central Страницы: 4

Бренд: Sysmac Страницы: 159

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды