EXFO FTB-860 Скачать руководство пользователя страница 82

Страница: 82 / 409

EtherSAM Test Setup and Results

FTB-860/880

Traffic - Statistics Results

Traffic - Statistics Results

From the

Test

menu, press

Results

Traffic

, and the

Statistics

tab.



Frame Type

: Displays the

TX Count

and

RX Count

of the number of

frames transmitted and received.



Multicast

: The number of Multicast frames transmitted/received

without any FCS errors. Broadcast frames are not counted as
multicast frames.



Broadcast

: The number of Broadcast frames transmitted/received

without any FCS errors. Broadcast frames have a MAC address
equal to

FF-FF-FF-FF-FF-FF



Unicast

: The number of Unicast frames transmitted/received

without any FCS errors.



Non-Unicast

: The sum of Multicast and Broadcast frames

transmitted/received without any FCS errors.



Total

: The number of frames transmitted/received without any FCS

error.

Содержание FTB-860


























































































































































































































































































































































































































Результаты поиска

Содержание FTB-860

Отзывы:

EXFO FTB-860, Руководство пользователя, Страница: 82 / 409

Результаты поиска

Содержание FTB-860

Отзывы: