EXFO FTB-860 Скачать руководство пользователя страница 323 | Manualshive

Страница: 323 / 409

EXFO FTB-860 Скачать руководство пользователя страница 323

Common Test Setup, Results, and Functions

NetBlazer

311

MAC/IP/UDP Configuration



Link-Local IPv6 Address

(LLA) is used for local communication

between on-link neighbors and for Neighbor Discovery process. Under

Link-Local IPv6 Address,

configure the following parameters.

Mode

:



StatelessAuto

allows automatic generation of the IPv6 address

based on the MAC address. The mode

StatelessAuto

is selected by

default.



Static

allows to enter the IP Address.

Address

: This field is configurable only when the

Mode

is

Static

. The

Link-Local IPv6 Address must start with FE80. The accepted range is
from

FE80:0000:0000:0000:0000:0000:0000:0000

to

FE80::0000:0000:0000:FFFF:FFFF:FFFF:FFFF

. The default address is

FE80::

[Interface ID], where [Interface ID] is generated from the source

MAC address. When the Address field is selected for editing using
virtual keyboard, the

Previous IP Addresses

button appears on the

screen. Press the corresponding function key to display the list of
previously configured IP addresses. Select the desired IP address from
the list, if any.



Global IPv6 Address

(GUA) is used to communicate with on-link

neighbors and for global communication with hosts outside the
subnet. Under

Global IPv6 Address

,

configure the following

parameters.

Mode

:



None

disables the Global IPv6 address and the Default Gateway

address.



StatelessAuto

allows automatic generation the IPv6 address based

on the Link-Local address interface ID and the prefix obtained
from the router advertisements. If no Interface ID has been
obtained for the Link Local Address, the Global address will not be
generated. The mode

StatelessAuto

is selected by default.



Static

allows you to enter the IP Address.

«
...
321
322
323
324
325
...
»

Содержание FTB-860


























































































































































































































































































































































































































Отзывы:

Нет отзывов