EXFO FTB-860 Скачать руководство пользователя страница 295

Страница: 295 / 409

Common Test Setup, Results, and Functions

NetBlazer

283

Interface - Port

Link



Auto-Negotiation:

Enable

Auto-Negotiation

, if the remote

connected port is also set to

Auto-Negotiation

, otherwise it should

be disabled. This is available only with the

10/100/1000 Mbit/s

Electrical

interface.



Speed

: Select the

Speed

of the interface.

When

10/100/1000 Mbit/s Electrical

is selected, the choices are

10 Mbit/s

100 Mbit/s

1 Gbit/s

(requires software option) and

Auto

(when

Auto-Negotiation

Enabled)

. The default setting is

100 Mbit/s

Note:

Speed is not available for optical interfaces.

Note:

When Speed is configured as

Auto

, the negotiated speed is displayed

beside the speed configuration parameter.



Duplex

: Select the

Duplex

mode. For

10 Mbit/s

and

100 Mbit/s

electrical interfaces, the choices are

Full

Half

, and

Auto

(when

Auto-Negotiation

Enabled)

. For

1000 Mbit/s

electrical interface

duplex is

Full

. Default is

Full

Note:

For

Auto

, the negotiated duplex is displayed beside the duplex

configuration parameter.

The following table shows the values for the

Duplex

Mode and

Flow

Control

with the different test applications.

Port Setup EtherSAM

RFC 2544

EtherB

ERT

Traffic Gen. Through Mode

Smart

Loopback

Duplex

Full / Auto

Half / Full

Full

Half / Full

Full / Half

Full

Flow

Control

None

None / RX

None

None / RX

None

Содержание FTB-860


























































































































































































































































































































































































































Результаты поиска

Содержание FTB-860

Отзывы:

EXFO FTB-860, Руководство пользователя, Страница: 295 / 409

Результаты поиска

Содержание FTB-860

Отзывы: