EXFO FTB-860 Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 409

EXFO FTB-860 Скачать руководство пользователя страница 29

Physical Interfaces and LEDs

NetBlazer

17

Ethernet 10 Gbit/s and FC 8X/10X Optical Port

Ethernet 10 Gbit/s and FC 8X/10X Optical Port

The FTB-860G, FTB-860GL, and FTB-880 provide one optical port for
10Gbit/s LAN/WAN Ethernet or 8X/10X Fibre Channel BERT testing.

The optical port is Small Form Factor Pluggable (SFP+) slot type.



Insert one of the following SFP+ modules into the optical slot.



Carefully connect optical fiber cables to the IN and OUT ports of SFP+.
To ensure good signal quality, make sure that the optical fiber
connector is fully inserted into the optical connector port.

LEDs

EXFO Part

Number

Description

FTB-8690 SFP+ module 10 GigE at 850 nm, MM, 300 m
FTB-8691 SFP+ module 10 GigE at 1310 nm, SM, 10 km
FTB-8692 SFP+ module 10 GigE at 1550 nm, SM, 40 km

LED

Status

Description

LASER
(Red)

On

An optical signal is generated

Off

No optical signal is generated

LINK/ACT
(Green)

On

Ethernet link up.

Off

Ethernet link down.

Flashing

TX/RX activity.

«
...
27
28
29
30
31
...
»

Содержание FTB-860


























































































































































































































































































































































































































Отзывы:

Нет отзывов