EXFO FTB-860 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 409

EXFO FTB-860 Скачать руководство пользователя страница 28

Physical Interfaces and LEDs

16

FTB-860/880

CPRI/OBSAI 2.0457/3.072 Gbit/s Optical Port

CPRI/OBSAI 2.0457/3.072 Gbit/s Optical Port

The FTB-860, FTB-860G, and FTB-880 provide one optical port for
CPRI/OBSAI 2.0457/3.072 Gbit/s testing.

The optical port is Small Form Factor Pluggable (SFP) slot type (Duplex LC
connector).



Insert one of the following SFP modules into the optical slot



Carefully connect optical fiber cables to the IN and OUT ports of SFP. To
ensure good signal quality, make sure that the optical fiber connector is
fully inserted into the optical connector port.

LEDs

EXFO Part

Number

Description

FTB-8590 GigE/FC/2FC, PRI/OBSAI 2.45/3.07 Gbit/s, 850 nm, <500 m
FTB-8190 155/622 Mbit/s, 2.5/2.7 Gbit/s, GigE/FC/2FC,

CPRI/OBSAI 2.45/3.07 Gbit/s, 1310 nm, 15 km

FTB-8191 155/622 Mbit/s, 2.5/2.7 Gbit/s, GigE/FC/2FC,

CPRI/OBSAI 2.45/3.07 Gbit/s, 1310 nm, 40 km

FTB-8192 155/622 Mbit/s, 2.5/2.7 Gbit/s, GigE/FC/2FC,

CPRI/OBSAI 2.45/3.07 Gbit/s, 1550 nm, 80 km

LED

Status

Description

LASER
(Red)

On

An optical signal is generated

Off

No optical signal is generated

LINK/ACT
(Green)

On

An optical signal is received

Off

Loss of signal (LOS)

«
...
26
27
28
29
30
...
»

Содержание FTB-860


























































































































































































































































































































































































































Отзывы:

Нет отзывов