manualshive.com logo in svg

EXFO FTB-860, Руководство пользователя, Страница: 205 / 409

Поделиться
Скачать
EXFO FTB-860 Скачать руководство пользователя страница 205

1588 PTP Test Setup and Results

NetBlazer

193

Summary (1588 PTP)

Delay Measurement 

Sync IPDV

 meter displays the average of the inter packet delay 

variation of consecutive Sync messages in the last second. The value 
and the pass/fail verdict is also displayed when enabled. 

Delay Req IPDV

 meter displays the average of the inter packet delay 

variation of consecutive Delay Req messages in the last second. The 
value and the pass/fail verdict is also displayed when enabled. 

Note:

When a value is below 1

μ

 second, “

< 1

μ

s

” is displayed. 

Note:

When the Pass/Fail verdict is enabled (see page 189), the green region is 
delimited from 0 to the IPDV Threshold (refer to 

PTP Alarm 

Timeout/Threshold

 on page 188) corresponding to a 

PASS

 verdict. The red 

region beyond the threshold corresponds to a

 FAIL

 verdict. There is neither 

green nor red region when the Pass/Fail verdict is disabled.

Quality Level 

Last QL Received

 indicates the last Quality Level received. The 

pass/fail verdict is also displayed when both 

QL Mismatch Monitoring

 

and 

Pass/Fail Verdict

 check boxes are selected. 

Last Change

 indicates the date and time of the Last QL change. 

Total PTP Messages 

Gives respectively the total count of transmitted (TX) and received (RX) 
PTP messages. 

Содержание FTB-860


























































































































































































































































































































































































































Отзывы:

Нет отзывов