EXFO FTB-860 Скачать руководство пользователя страница 163

Страница: 163 / 409

Smart Loopback Test Setup and Results

NetBlazer

151

Summary Results

Loopback Mode



Loopback Mode

: The

Loopback Mode

parameter shall determine at

which layer the address/port swapping is limited. Select the

Loopback

Mode

. Choices are:



UDP/TCP

: Swap MAC addresses, IP addresses, UDP or TCP ports

when present and addressed to unit own MAC/IP. In other words,
swap from Layer 2 up to Layer 4 when present.



: Swap MAC addresses, IP addresses when present and

addressed to unit own MAC/IP. In other words, swap from Layer 2
up to Layer 3 when present.



Ethernet

: Swap MAC addresses when addressed to unit own MAC.

In other words, swap Layer 2 when present.



Ethernet (All Unicast)

: Swap MAC addresses when the address is

unicast, regardless if it is unit’s own MAC or not.



Transparent

: Loopback everything without swapping anything.

By default,

UDP/TCP

will be selected.

Note:

When remote unit is looped up where

Remote Capability

Remote

Loopback

, the Smart Loopback test runs with loopback mode as

“UDP/TCP” on remote.

Note:

The

Transparent

mode is not intended to be used in switched or routed

networks (i.e. only point-to-point).



Rate Unit

: Select the rate unit as

Mbit/s

Gbit/s

Содержание FTB-860


























































































































































































































































































































































































































Результаты поиска

Содержание FTB-860

Отзывы:

EXFO FTB-860, Руководство пользователя, Страница: 163 / 409

Результаты поиска

Содержание FTB-860

Отзывы: